Stainless steel equipment for rooms that get audited.
Manufacturer, supplier and exporter of stainless steel equipment and furniture for pharmaceutical, biotechnology, hospital and commercial kitchen environments. Custom SS fabrication built to your drawings.
- Years fabricating
- 14+Years fabricatingServing Pune and export markets
- Product families
- 6Product familiesCleanroom through material handling
- Grades worked
- 304 / 316LGrades workedSelected per application
- Standard practice
- Made to orderStandard practiceDrawings, not catalogue sizes
Six families, built to order
The sizes below are what we make most often. Almost everything is fabricated to a customer drawing.
01Cleanroom Equipments
Air handling and containment units for classified areas.
9 products
02Cleanroom Furniture
Gowning, storage and work surfaces that clean down properly.
13 products
03Cleanroom Accessories
The small stainless items a classified area runs on.
9 products
04Hospital Furniture
Ward, theatre and storage furniture built for daily disinfection.
10 products
05Kitchen Equipments
Cooking, holding and wash-up for canteens and institutions.
7 products
06Material Handling Equipment
Moving drums, pallets and containers without injuring anyone.
8 products
A sample of what we build
Drawings shown are representative. Sizes, grade and finish are set per order.
Laminar Air Flow
Horizontal or vertical unidirectional flow over the work zone, Grade A at the face.
Specification
SS Pass Box
Interlocked transfer hatch between areas of different classification.
SpecificationSS Cross Over Bench
Divides a gowning room into unclassified and classified sides.
Specification
SS Lockers
Personnel lockers in stainless or powder-coated steel, up to 20 compartments.
SpecificationHospital Beds
Fowler, semi-fowler and plain beds with SS framing.
SpecificationGas Range
Two, four or six burner ranges with a drained top.
Specification
Scissor Lift
Adjusts working height so nobody bends to a pallet.
Specification
SS Samplers
Thief and dip samplers for powders and liquids.
Specification
A fabricator that draws before it cuts
Nothing goes on the shop floor before a general arrangement drawing is signed off. It is slower at the start and considerably faster afterwards.
- 01
Built to your drawing
Most of what leaves the works is made to a customer drawing or a site measurement, not picked from a catalogue. Send a GA drawing or a sketch with dimensions and we will quote against it.
- 02
Finishes that survive validation
SS 304 and SS 316L as the application demands, with mirror, matt or bead-blasted finishes. Welds ground flush and passivated so there is nowhere for residue to sit.
- 03
Documentation with the equipment
Material test certificates, weld maps, and IQ/OQ documents supplied where the installation is being qualified. Auditors ask for paperwork, not promises.
- 04
In-house fabrication
Cutting, forming, welding, grinding and assembly under one roof in Hadapsar. Nothing critical is subcontracted, so the schedule is ours to hold.
Where this equipment ends up
Different rooms, the same constraints: it has to clean down, hold up and be evidenced.
Pharmaceutical
Equipment for classified areas where the finish, the documentation and the airflow all have to survive an audit.
Read moreBiotechnology
Containment and clean-air equipment for laboratory and pilot scale work.
Read moreHospitals and healthcare
Ward, theatre and CSSD furniture built for repeated disinfection.
Read moreFood processing
Washdown-grade equipment for food manufacturing areas.
Read moreCommercial kitchens
Cooking, holding and wash-up for canteens, hospitals and institutions.
Read more
Enquiry to installation
Four stages, and you approve the drawing before anything is cut.
- 01
Requirement
Share a drawing, a sketch or the site constraint. For cleanroom work, tell us the classification and the room it has to fit.
- 02
Drawing and quotation
We return a GA drawing with the bill of material, grade, finish and price. Nothing is fabricated before you sign it off.
- 03
Fabrication
Cut, formed, welded and finished at the works. Stage photographs on request for equipment being made against a project schedule.
- 04
Despatch and installation
Packed for transport, delivered and installed where the scope includes it, with documentation handed over on site.
Send us a drawing and we will quote against it.
A GA drawing, a dimensioned sketch or a photograph with the constraint written on it — all of them are enough to start.